How to Fix a Swamp Cooler Bottom From Leaking?

The spilling of water from air coolers is one of the most prevalent ongoing issues that most users experience. Although it’s clear which water is flowing from, especially if it is the water you have set in the device, it’s unclear what’s triggering the water storage tank to leak.

Water dripping from the swamp cooler or air cooler might be due to a basic overflowing of the water tank, or it might be due to a cracked or improperly connected water tank. It may be that the moisture or water honeycomb padding is cracked, allowing the water to escape. The issue may persist if it remains unfixed for a longer time.

Luckily, the article describes the common causes of the issue and gives the best steps to fix it successfully. Also, it includes the frequently asked questions concerning the swamp cooler base that is leaking. Therefore, ensure you fix the issue instantly or seek help.

Common causes of Swamp Cooler Bottom LeakingCommon causes of Swamp Cooler Bottom Leaking

Most people may experience the issue of the swamp cooler bottom leaking. These are the most prevalent causes of an air cooler that leaks.

  • The honeycomb pad is faulty

When washing, the honeycomb pad, commonly known as the water-soaked pad that the air flows via, may become faulty or fail to function as usual. It may be unable to contain water and spill it all over your ground due to this. In such circumstances, it is important to solve the issue immediately before it becomes worse and damages your floor.

  • Overflowing

You may have overloaded your swamp cooler or air cooler, which is causing it to leak water. The ice chamber on models with an ice chamber may have already melted and overflowed.

  • A leaking water tank

If the water is pouring from your swamp or air cooler base, the water storage tank may leak it. Although corrosion will not be a concern because most water tanks are made of plastic, unintentional perforating during washing or installation may occur.

  • The honeycomb pad has incorrect fittings

It’s possible that if you place the honeycomb pad improperly, it can spill water. Additionally, if you purchase a repair pad in the incorrect size, it may not absorb the water properly.

  • Open water

If the water tank is not returned to its appropriate places, water may escape. Devices with a removable water tank are more prone to issue of leakages.

Steps on how to Fix a Swamp Cooler Bottom from LeakingFix a Swamp Cooler Bottom from Leaking

The swamp cooler leaking is a common problem affecting many users, and it can be due to several reasons such as loose water lines, floating pipes, among others. If you experience such issues, it is important to fix the issue immediately before it becomes worse. The steps below give a clear guide on how to solve the issue.

Step 1: Collect all essential materials

The materials necessary include the following;

  1.  Cleaning agents such as White Vinegar 
  2. Paint Brush Cooler
  3. Coating Sealant
  4.  Antistatic wrist band.
  5.  Screwdriver.

To get the sealing to attach to the base, you’ll have to wash it thoroughly. White vinegar is typically in use to remove dirt and corrosion, and it is occasionally left sitting longer. The sealer, as well as a brush to apply it, will be necessary.

Step 2: Switch off the power source

First, locate the position of the power supply source and disconnect the swamp cooler from the source. The only way to carry such a process is by turning the power source off. Before turning it off, ensure you wear an antistatic wrist band to protect yourself from any power faults such as electric shock. Proceed to the next step.

Step 3: Locate all the swamp cooler panels and remove them carefully

First, check the swamp cooler carefully and identify any faults. Find the position of all panels, especially the side panel. Carefully remove the side panel to access the internal parts of the swamp cooler. While removing the side panel, pay more attention to every part to avoid damaging any part.

Step 4: Inspect the internal parts

Check all the parts of the swamp cooler and identify any faults. Check the water tank and see if there are any cracks. Also, check the water tank if it is in the correct position and if it is loose. Proceed to fix the issue depending on the main cause.

Step 5: Remove the swamp cooler floatRemove the swamp cooler float

Check the location of the float and remove it gently. Look at it carefully and identify any faults present. If the float has some damage beyond repair, consider replacing it with a new one functioning correctly. When buying the replacement float, ensure it matches with the swamp cooler and is functioning correctly.

The best way to get the accurate float is by buying from an original or an open shop such as amazon.com and ebay.com. If you fix the float but the issue persists, proceed to the next steps carefully.

Step 6: Check the drain pipe

The drain pipe, in most cases, is the one at fault. Carefully find its position and remove it. Inspect the drain plug if it is in good condition. If it has some cracks, seal it using the sealing agent, but if it has some damage that is difficult to repair, consCheck the water tankider replacing it with a new one that suits the swamp cooler perfectly.

Step 7: Check the water tank

Sometimes, the main reason for the swamp cooler leak is a broken water tank. To fix the issue, seal using the sealing agent. First, apply the elastomeric sealer at the crack position hole if small enough. If your device is still in the warranty period, consider contacting the seller for replacement rather than buying a new one. Also, if the hole is too big and difficult to replace, buy a new one and follow the manufacturer’s instructions on how to fix it correctly.

If the water tank is loose, allowing water to spill, switch off the swamp cooler unit and ensure no water is present or flowing in and out of the tank. Remove it gently from its position and reinstall the water tank properly. See if the issue is eliminated. If not, proceed to the next step.

Step 8: Fix the honeycomb pad

Most of the time, the leaks are due to loose, incorrect, or improperly installed honeycomb. To fix such an issue, first, switch off the water supply source and check if the honeycomb pad is the correct one or if it is properly installed. If bad, replace the honeycomb pad and consider installing it properly while following the manufacturer’s instructions.

Reinstall a new honeycomb pad that suits the swamp cooler if faulty. When installing it, ensure the size is compatible and is functioning correctly. Also, seek a replacement if the honeycomb pad is still in the warranty period. Also, if the honeycomb is faulty or broken, seek help from an expert if it is not possible to replace it on your own.

Step 9: Check if the water in the water tank is overflowing

The issue is simple to fix, even without any steps. Look at the water level, ensure it is at the marked level when pumping, and avoid moving or tilting the swamp cooler if it is full. Tilt it after flowing water out for some time. Finally, avoid leaving the swamp cooler empty.

Step 10: Clean the bottom of the swamp cooler

First, clean the bottom of the swamp cooler using the correct agent, especially the white vinegar. Ensure you remove all dirt and organic debris and rinse it using clean water. Leave it for a couple of minutes until it is completely dry. When cleaning the bottom of the brush to coat the base of the cooler and the waterline.

Step 11: Reinstall all parts correctly

After fixing all the parts, reinstall all of them back to their position. Start with the internal parts, the drain plug, and water float, among others. Test to see if the issue is eliminated; if it persists, seek help from an expert to help you fix the issue.

Frequently asked questions:

It’s critical to replace your evaporative cooler pads on a routine basis if you want to maintain your swamp cooler running at its best. The pads in your cooler are working hard to keep the air cool, and while they do so, they begin to accumulate deposits.

As a result, the efficiency of your cooler will begin to deteriorate, resulting in reduced cooling capabilities. Premier Industries Inc. has a lot of experience with swamp coolers and cooler pads, and we have a few suggestions to help you figure out when it’s time to replace your evaporative cooler pad.

Conclusion

With the correct sealant, fixing the base of a dripping swamp cooler is simple. For the sealer to hold, the unit’s base must be kept clean; else, it may slip off. Ensure the base is well-clean with white vinegar. After a coating is applied to the base of an old swamp cooler, it can last for many more years. Cushions, engines, floats, and compressors are among the other elements that have perfect replacement.

At the worst, dripping water from your air cooler is an annoyance, but it is readily avoidable by simply being vigilant. The repairs are also simple enough for you to complete on your own. Success in fixing your swamp cooler.

Leave a Comment